dc.contributor.author | Lima, Amanda Santos de | |
dc.date.accessioned | 2024-07-18T11:27:07Z | |
dc.date.available | 2024-07-18T11:27:07Z | |
dc.date.issued | 2024-04-18 | |
dc.identifier.citation | LIMA, Amanda Santos de. Estudo da influência da composição em materiais compósitos de polipropileno com fibras de vidro por pultrusão termoplástica nas propriedades mecânicas. 2024. Tese (Doutorado em Química) – Universidade Federal de São Carlos, São Carlos, 2024. Disponível em: https://repositorio.ufscar.br/handle/ufscar/20082. | * |
dc.identifier.uri | https://repositorio.ufscar.br/handle/ufscar/20082 | |
dc.description.abstract | The objective of this work is to evaluate manufacture variations over thermoplastic
composite materials of polypropylene reinforced with glass fibers (FV) regarding
their tensile and flexural mechanical properties (PMs). The samples are produced
by a partner company located in São Carlos - SP, Brazil, and manufacture
variation are as described: geometry of the heated die (pin, MP, and waves, MO),
the use and the position of the conformer (d = 0 of the heated die, upper part of
the conformer at d = 0 and the lower part at a distance “d” and completely away
at a distance “d”), pulling speed (7 and 15 m/min), fibers with different surfaces
and different concentrations of maleic anhydride (MA). The results show that the
crystallinity of the materials was influenced by geometry of the heated die (MP ~
28% and MO = 39%). The position of the conformer was shown to influence the
PMs and the crystallinity, which the material C2.O1122-CM, at position d = 0,
had the lowest tensile (73 MPa) and flexural (67 MPa) values and the highest
crystallinity value (~35%) within the sample of the group with conformer.
Through the optical microscopy it shows that the conformer did not perform well
on providing a cylindrical and uniform pellet. The variations of pulling speed
showed that it influences crystallinity (C2.O115 ~ 34% and C2.O215 ~ 30%) but
there is no difference in PMs. Through a multivariate analysis of the group of the
samples with variation of FV and MA, it was possible to observe the influence of
each variable on the PMs and verify that the best condition was achieved with an
intermediate FV texture and lower concentration of MA with the sample C2.O212
(tensile ~ 91 MPa and flexural = 163 MPa). | eng |
dc.description.sponsorship | Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq) | por |
dc.language.iso | por | por |
dc.publisher | Universidade Federal de São Carlos | por |
dc.rights | Attribution-NonCommercial-NoDerivs 3.0 Brazil | * |
dc.rights.uri | http://creativecommons.org/licenses/by-nc-nd/3.0/br/ | * |
dc.subject | Polipropileno | por |
dc.subject | Fibra de vidro | por |
dc.subject | Anidrido maleico | por |
dc.subject | Geometria da matriz | por |
dc.subject | Conformador | por |
dc.subject | Velocidade de pultrusão | por |
dc.subject | Polypropylene | eng |
dc.subject | Glass fiber | eng |
dc.subject | Maleic anhydride | eng |
dc.subject | Geometry of the heated die | eng |
dc.subject | Conformer | eng |
dc.subject | Pulling speed | eng |
dc.title | Estudo da influência da composição em materiais compósitos de polipropileno com fibras de vidro por pultrusão termoplástica nas propriedades mecânicas | por |
dc.title.alternative | Study of the influence of composition in composite materials of polypropylene with glass fibers by thermoplastic pultrusion on mechanical properties | eng |
dc.type | Tese | por |
dc.contributor.advisor1 | Souza, Ernesto Chaves Pereira de | |
dc.contributor.advisor1Lattes | http://lattes.cnpq.br/1505400360366643 | por |
dc.description.resumo | Este trabalho teve como objetivo avaliar materiais compósitos termoplásticos de
polipropileno reforçado com fibras de vidro (FV) quanto as suas propriedades
mecânicas (PMs) de tração e flexão com variações de: geometria da matriz de
aquecimento (matriz de pinos, MP, e matriz de ondas, MO), uso e posição do
conformador (d = 0 da matriz, parte superior do conformador a d = 0 e a parte
inferior a uma distância “d” e totalmente afastado a uma distância “d”), velocidade
de pultrusão (7 e 15 m/min), fibras com diferenças superficiais e concentrações
diferentes de anidrido maleico (MA) produzidos por uma empresa localizada em
São Carlos. Foi observado que a cristalinidade dos materiais foi influenciada pela
geometria da matriz (MP ~ 28% e MO = 39%). A posição do conformador
mostrou influenciar nas PMs e na cristalinidade, sendo que o material C2.O1122-
CM, na posição d = 0, teve os menores valores de tração (73 MPa) e flexão (67
MPa) e o maior valor de cristalinidade (~ 35%) dentro do conjunto de amostras
com conformador. Através da microscopia óptica foi observado que o
conformador não exerceu a função de proporcionar um pellet cilíndrico e
uniforme. O estudo da velocidade de pultrusão mostrou que o seu aumento
influencia na cristalinidade (C2.O115 ~ 34% e C2.O215 ~ 30%) porém não há
diferença nas PMs. Através de uma análise multivariada do conjunto de amostras
com variação de FV e MA foi possível observar a influência de cada variável nas
PMs e constatar que a melhor condição foi atingida com a FV de textura
intermediária e a menor concentração de MA, com a amostra C2.O212 (tração ~
91 MPa e flexão = 163 MPa). | por |
dc.publisher.initials | UFSCar | por |
dc.publisher.program | Programa de Pós-Graduação em Química - PPGQ | por |
dc.subject.cnpq | CIENCIAS EXATAS E DA TERRA::QUIMICA | por |
dc.description.sponsorshipId | Processo nº 159189/2019-5, Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq) | por |
dc.publisher.address | Câmpus São Carlos | por |
dc.contributor.authorlattes | http://lattes.cnpq.br/2173334718153901 | por |