Listar Teses e dissertações por título
Mostrando ítems 616-635 de 732
-
Propriedades de armazenagem de hidrogênio do intermetálico TiFe processado por moagem de alta energia e laminação a frio sob atmosfera controlada
(Universidade Federal de São Carlos, UFSCar, Programa de Pós-Graduação em Ciência e Engenharia de Materiais - PPGCEM, Câmpus São Carlos, 27/03/2017)TiFe is a material of practical interest for hydrogen storage due to its absorption capacity of ~ 1.9 wt. % H at room temperature and the relative low cost of its constituent elements. However, this intermetallic requires ... -
Propriedades mecânicas das ligas Ti34Cu36Ni8Zr22 e (TiZr)80Co12Fe8
(Universidade Federal de São Carlos, UFSCar, Programa de Pós-Graduação em Ciência e Engenharia de Materiais - PPGCEM, , 23/03/2012)Bulk amorphous and nanocrystalline alloys have attracted great interest from the scientific community. Titanium based alloys have demonstrated potential for formation of amorphous. This study aimed at to evaluate the ... -
Propriedades mecânicas de tração e impacto dos aços inoxidáveis CA15 e CA6NM
(Universidade Federal de São Carlos, UFSCar, Programa de Pós-Graduação em Ciência e Engenharia de Materiais - PPGCEM, , 27/02/2007)The subject of this work was to study the mechanical properties, based in tensile and impact tests, of two stainless martensitic steels cast under designations of ASTM Standards, namely the CA15 steel, a steel with 12% of ... -
Propriedades mecânicas e correlação dos parâmetros de FSW e DS-FSW em alta velocidade na liga AA2050-T84, para a indústria aeronáutica
(Universidade Federal de São Carlos, UFSCar, Programa de Pós-Graduação em Ciência e Engenharia de Materiais - PPGCEM, Câmpus São Carlos, 19/11/2018)Friction Stir Welding (FSW) and DS-FSW (double pass FSW) processes were employed in the aluminum AA 2050 T-84 plate joints aiming to make possible to increase the welding speed above 5 mm / s, to obtain welds with optimized ... -
Prospecção tecnológica em materiais: aumento da eficiência do tratamento bibliométrico. Aplicação na análise de tratamentos de superfície resistentes ao desgaste.
(Universidade Federal de São Carlos, UFSCar, Programa de Pós-Graduação em Ciência e Engenharia de Materiais - PPGCEM, , 07/12/2001)Nowadays, there is a wide information bulk in accelerated increase that needs high efficiency of analysis to the decision maker. Databases spreading become more important the production of indicators to technological ... -
Reaproveitamento de resíduos da agroindústria da laranja para a produção de compostos biodegradáveis em matriz de PBS
(Universidade Federal de São Carlos, UFSCar, Programa de Pós-Graduação em Ciência e Engenharia de Materiais - PPGCEM, Câmpus São Carlos, 24/09/2021)The employment of biodegradable polymers is a partial solution to the problem of environmental plastic pollution, since conventional polymers are resistant to many environmental influences and it may take centuries for ... -
Reatividade de materiais de moldagem na fundição de precisão de titânio
(Universidade Federal de São Carlos, UFSCar, Programa de Pós-Graduação em Ciência e Engenharia de Materiais - PPGCEM, , 13/04/2009)Investment casting of Titanium parts free of defects is very difficult owing to the reactivity of this element in the liquid state .The objective of this study was to evaluate the reactivity of titanium with refractory ... -
Rebitagem por fricçao de alumínio 2024-T351 em policarbonato
(Universidade Federal de São Carlos, UFSCar, Programa de Pós-Graduação em Ciência e Engenharia de Materiais - PPGCEM, , 24/10/2014)This dissertation addressed the feasibility study of Friction Riveting technique on polycarbonate and 2024-T351 aluminum alloy spot joints. Design of experiments and Artificial Neural Network modelling were used to investigate ... -
Reciclagem de cavacos de ligas de alumínio 7050-T7451 utilizando conformação por spray e tratamentos termomecânicos
(Universidade Federal de São Carlos, UFSCar, Programa de Pós-Graduação em Ciência e Engenharia de Materiais - PPGCEM, , 09/08/2012)The aim of this work is to conjugate a sort of known processing techniques in to a machining chips recycling route. These are generate during airframe primary parts from AA 7050-T7451, purchased according to AMS 4050H. The ... -
Reciclagem de embalagens flexíveis multicamadas
(Universidade Federal de São Carlos, UFSCar, Programa de Pós-Graduação em Ciência e Engenharia de Materiais - PPGCEM, Câmpus São Carlos, 29/04/2022)Packaging industry is facing an important paradox in flexible plastic packaging for fresh food. While, food waste is avoided using multilayer and multi-material structures with barrier properties, that increase shelf life ... -
Reciclagem química de PET proveniente de filtros industriais pós-consumo
(Universidade Federal de São Carlos, UFSCar, Programa de Pós-Graduação em Ciência e Engenharia de Materiais - PPGCEM, , 10/03/2006)The PET filter bag is used in the separation of the particulates materials of the gas produced in the aluminum industry. It had been submitted a chemical recycling. Almost industries make the disposal of these materials ... -
Recobrimentos de ligas Ti-Nb-Zr depositados por pulverização magneto-catódica sobre aço inoxidável AISI 316L para aplicações biomédicas
(Universidade Federal de São Carlos, UFSCar, Programa de Pós-Graduação em Ciência e Engenharia de Materiais - PPGCEM, Câmpus São Carlos, 30/11/2022)The work consists of the deposition of Ti-Nb-Zr ternary alloy coatings in the form of thin films on an AISI 316L stainless steel substrate for applications in the biomedical area, such as dental or orthopedic prosthesis. ... -
Refill friction stir spot welding of AA6016-T4 aluminum alloy: study of new load-controlled process
(Universidade Federal de São Carlos, UFSCar, Programa de Pós-Graduação em Ciência e Engenharia de Materiais - PPGCEM, Câmpus São Carlos, 29/06/2020)Aiming at structural weight reduction and energy efficiency, aluminum alloys have been considered as potential materials for automobile manufacturing. The development of technologies able to join aluminum alloys more ... -
Refill friction stir spot welding of different thickness Al-Cu alloy using a tool with reduced dimensions for aerospace application
(Universidade Federal de São Carlos, UFSCar, Programa de Pós-Graduação em Ciência e Engenharia de Materiais - PPGCEM, Câmpus São Carlos, 12/11/2020)Refill Friction Stir Spot Welding has grown as an interesting alternative to conventional joining techniques in recent years, especially when it comes to high strength aluminum alloys. Although current results show promise, ... -
Refill Friction Stir Spot Welding: evaluation of the welding of AA2198-T8 sheets and preliminary tool wear investigation
(Universidade Federal de São Carlos, UFSCar, Programa de Pós-Graduação em Ciência e Engenharia de Materiais - PPGCEM, Câmpus São Carlos, 26/04/2019)Refill Friction Stir Spot Welding (RFSSW) is an innovative method for joining similar and dissimilar lightweight metallic materials or thermoplastics. This technique has the advantage of issuing energy savings, producing ... -
Refill friction stir spot welding: investigation of the similar and dissimilar welding of AA5754-H22 and AA6061-T6 sheets
(Universidade Federal de São Carlos, UFSCar, Programa de Pós-Graduação em Ciência e Engenharia de Materiais - PPGCEM, Câmpus São Carlos, 03/06/2019)The automotive industry is shifting to a new paradigm of material utilization in vehicles. Different parts of the car structural body are increasingly being made of materials selected to have a customized performance ... -
Refino de grão na transformação austenítica em aço rolamento previamente conformado a frio
(Universidade Federal de São Carlos, UFSCar, Programa de Pós-Graduação em Ciência e Engenharia de Materiais - PPGCEM, , 07/08/2012)In this work is presented the characteristics of the steel C80U Modified, usually applied for bearing components produced through cold forming, as evaluated the influence of prior cold work on the microstructure after heat ... -
Refratários avançados sinterizados com líquidos transientes
(Universidade Federal de São Carlos, UFSCar, Programa de Pós-Graduação em Ciência e Engenharia de Materiais - PPGCEM, Câmpus São Carlos, 09/03/2017)Sintering additives (AS) have great potential to be applied in refractory castables as they reduce the densification temperature of these products. Additionally, these components may induce the generation of a transient ... -
Refratários para o transporte de alumínio líquido: fundamentos, simulação e prática industrial
(Universidade Federal de São Carlos, UFSCar, Programa de Pós-Graduação em Ciência e Engenharia de Materiais - PPGCEM, , 13/09/2007)Not only for the development of their products, the aluminum industry has engaged its efforts in services for their customers. One of them is the molten aluminum delivery (7 to 8 t) in crucibles for long distances (over ... -
Refusão superficial a laser da liga com memória de forma Cu-11,8Al-3,2Ni-3Mn (% Peso)
(Universidade Federal de São Carlos, UFSCar, Programa de Pós-Graduação em Ciência e Engenharia de Materiais - PPGCEM, Câmpus São Carlos, 10/02/2017)Shape memory alloys (SMA) are alloys that undergo martensitic transformation due to an external solicitation (temperature, stress, strain or magnetic field) and are capable of recovering permanent deformation when heated ...