Buscar
Itens para a visualização no momento 41-50 of 175
Caracterização da interface de tubo bimetálico cladeado fundido por centrifugação
(Universidade Federal de São Carlos, 2015-03-27)
Bimetallic pipes represent a solution for cost reduction to pipelines in the oil and
gas industry, because they combine two materials with distinct characteristics in
the pipe manufacturing: a HSLA steel, constituting ...
Efeitos de degradação e de alterações microestruturais do polímero no desempenho mecânico estático de juntas híbridas de polieterimida (PEI) e alumínio produzidas por F-ICJ
(Universidade Federal de São Carlos, 2016-02-29)
This master thesis aims to study hybrid joints of polyetherimide (PEI) and aluminum 6082-T6 produced by Friction-based Injection Clinching Joining (FICJ). The influences of the process parameters in the frictional heat and ...
Compatibilização química em compósitos de PLA reforçados com fibras de sisal
(Universidade Federal de São Carlos, 2018-07-13)
Even though poly(lactic acid) (PLA) is fragile under impact and has low toughness, the polymer stands out for its stiffness and high tensile strength. This polymer is an interesting material not only for short-term ...
Desenvolvimento de Nanoblendas PLA/EVOH biodegradáveis com características de barreira a gases e vapores
(Universidade Federal de São Carlos, 2018-07-20)
Poly (lactic acid) (PLA) is a non-toxic, transparent and biodegradable aliphatic polyester, produced from renewable raw materials. This polymer meets several requirements for packaging applications, but is fragile and has ...
Ligas Sn-Ni: efeitos da taxa de resfriamento e da microestrutura nas propriedades mecânicas de tração
(Universidade Federal de São Carlos, 2018-02-28)
The present investigation examined the microstructural arrangements formed during the transient solidification of the eutectic Sn-0.2wt.%Ni and the hypereutectic Sn-0.5wt.%Ni alloys using two different substrates as mold ...
Correlações entre microestrutura, parâmetros térmicos e propriedades mecânicas de ligas de alumínio da série 5xxx solidificadas unidirecionalmente
(Universidade Federal de São Carlos, 2017-08-04)
Processing high-Mg content Aluminum Alloys by continuous casting technics is considered an industry challenge. The present research aims to characterize 5xxx alloy series, considering composition based on the commercial ...
Monitoramento em tempo real da cristalização quiescente e induzida por fluxo de polipropileno em microscópio óptico de luz polarizada
(Universidade Federal de São Carlos, 2015-08-07)
In the polymer forming processes, such as injection molding, extrusion of films / sheets and blowing, these materials are subject to shearing and elongation flows. Such conditions influence its final morphologies. When ...
Otimização dos parâmetros de soldagem a ponto por Fricção (FSpW) da liga AlMgSc e avaliação das propriedades mecânicas estáticas e dinâmicas
(Universidade Federal de São Carlos, 2017-08-28)
Aluminum alloys are widely used in transportation industry to reduce structural weight and fuel consumption. The development of advanced alloys and more effective technologies for joining materials contribute to achieve ...
Desenvolvimento de protótipo de sensor de umidade cerâmico
(Universidade Federal de São Carlos, 2012-08-24)
Humidity sensor is a special type of gas sensor which is sensitive only to H2O molecules. It has a large variety of applications in industrial, household and agricultural equipments. Humidity ceramic sensors have been ...
Estudo dos efeitos do biodiesel e suas misturas com óleo diesel em materiais metálicos
(Universidade Federal de São Carlos, 2017-03-09)
The use of biodiesel in vehicles can significantly reduce dependence on fossil fuels and help to reduce environmental pollution. However, there are concerns about the compatibility of automotive materials in contact with ...