Buscar
Itens para a visualização no momento 1-10 of 10
Desenvolvimento de concentrados de PVC reforçados com fibras de vidro longas (LF-PVC) para reforçar compostos de PVC rígido moldados por injeção
(Universidade Federal de São Carlos, 2013-12-06)
This work presents a study and development of long glass fiber PVC pellet concentrate (LF-PVC) manufactured by extrusion similar wire coating technique to reinforce pelletized rigid PVC compounds to produce injection molding ...
Propriedades mecânicas das ligas Ti34Cu36Ni8Zr22 e (TiZr)80Co12Fe8
(Universidade Federal de São Carlos, 2012-03-23)
Bulk amorphous and nanocrystalline alloys have attracted great interest from the scientific community. Titanium based alloys have demonstrated potential for formation of amorphous. This study aimed at to evaluate the ...
Deformação em canal angular de uma liga Al-4%Cu: efeito dos mecanismos de endurecimento na resistência mecânica e ductilidade
(Universidade Federal de São Carlos, 2011-03-03)
Internal boundaries hardening and precipitation hardening are two important mechanisms acting in metallic alloys. The former has special relevance when the grain size is reduced ...
Estudo do processo de soldagem a ponto por fricção de juntas dissimilares entre ligas de alumínio e titânio
(Universidade Federal de São Carlos, 2016-12-09)
Multimaterial structures between aluminum and titanium alloys are a
technologically attractive field of research and their increasing use in the
transportation sector for weight and emission reduction is part of the ...
Comportamento mecânico em fadiga da liga de titânio beta metaestável Ti-5553
(Universidade Federal de São Carlos, 2016-10-14)
The microstructure of metastable beta Ti alloys is a decisive factor that
governs their properties and, therefore, the assessment of the relation between
the microstructure and the fatigue response means an advance in ...
Avaliação das microestruturas de solidificação e propriedades de aplicação de ligas monotéticas Al-Bi, Al-Bi-Cu e Al-Bi-Zn
(Universidade Federal de São Carlos, 2021-06-16)
Monotectic Al-based ternary alloys can result in a good combination of wear resistance and mechanical strength. While the soft self-lubricating elements contribute to an appropriate wear resistance, modification with third ...
Influência das condições de processamento na morfologia e das propriedades mecânicas de sistemas poliméricos moldados por injeção e sua predição através de redes neurais artificiais.
(Universidade Federal de São Carlos, 2004-08-12)
The influence of the injection molding parameters on the morphology and mechanical properties of poly(phenylene sulfide), PPS, and of a 80/20(%wt) blend of PPS/block copolymer styrene-ethylene-butylene-styrene ,SEBS, ...
Microestrutura e propriedades mecânicas de ligas Al-Si hipoeutéticas conformadas por spray.
(Universidade Federal de São Carlos, 2005-06-29)
The aims of this work were the microstructural and tensile properties
characterization of the hypoeutectic spray formed Al-Si 319 and 380 alloys. The
alloys were melted by induction furnace, gas atomized with nitrogen ...
Avaliação do dano por choque térmico em concretos refratários via espectroscopia acústica ressonante não-linear
(Universidade Federal de São Carlos, 2012-03-02)
In this thesis the Non-linear Resonant Acoustic Spectroscopy Technique used to evaluate the mesoscopic non-linearity was incorporated into the Impulse Excitation Technique, which is extensively applied to the evaluation ...
Desenvolvimento de vitrocerâmicos transparentes resistentes ao impacto
(Universidade Federal de São Carlos, 2021-11-11)
Transparent glass-ceramics (GCs) can replace glasses traditionally used as ballistic windows and electronic displays due to their better mechanical properties. This improvement is obtained by the crystallization of phases ...